Share/Bookmark Print

Standard Fiberglass Doors

Standard smooth-skinned fiberglass door (#686-OXF SS) and sidelites (#694-OXF SS) with Oxford decorative glass.

Standard Fiberglass Doors

  • Oak texture or smooth skin
  • Doors & sidelites with or without raised panels
  • Glass options including 9 decorative designs
  • Performance divided lites
  • Grilles-in-the-airspace
  • Flush-glazed doors
  • Blinds between the glass
  • Venting doors
  • Factory finish in 5 stain colors
  • Exterior factory finish in over 50 colors
  • Inswing or outswing operation
  • Wide variety of handle set, lock & sill options
  • Wood frames with or without extruded aluminum clad exterior

Panel Details

Construction

  • Fiberglass reinforced door skins
  • Full-length, high-strength, engineered composite stiles and top & bottom rails prevent moisture seepage
  • High-impact compression molded skins won't splinter, warp or rot
  • Environmentally-friendly polyurethane core provides high insulation properties

Textures

Each Standard fiberglass panel is available with either a Oak wood grain texture or a smooth skin.

  • Standard
    Textured (ST)
  • Standard Smooth
    (SS)

NOTE: Venting panels are only available with a smooth skin.

Glass

Decorative Glass Options

Nine decorative glass designs are available for most Standard fiberglass door and sidelite panels, except those with blinds or venting panels. Detailed information is available by following the links at left for each glass design (ex: Capella, Catalina, Solitude, etc.).

Decorative glass varies widely in the amount of privacy it affords. Each is given a privacy rating from 1 to 10, so you can choose the right amount of opacity for you. 

Privacy ratings and detailed glass information is available for each decorative glass design by following the links at left (ex:CapellaCatalinaSolitude, etc.).

NOTE: Door glass is tempered for safety.

NOTE:

These glass options apply to most Standard panels, but do not apply to panels with blinds or venting panels. Glass details for those units are found by following the links at left for Panels with Blinds and Venting Panels.

+
Glass Terminology
Standard - Double Pane Glass

Double pane glass* achieves energy efficiency across various climate zones

  1. Double pane insulating glass unit
  2. LoE²-270 (for optional LoE coatings, see Glass Terminology)
  3. Argon gas (for exceptions, see Glass Terminology)
  4. Thermo-Edge, stainless steel spacer bars

*Double pane glass is standard for most Kolbe products. Size and other limitations may apply. In doors, both panes are tempered for safety. Windows may be ordered tempered as well, which may be required due to the glass size and/or to meet local building codes.

Option - ThermaPlus Coating

ThermaPlus is an optional interior coating that can be applied to help meet the strictest energy requirements, helping provide protection against heat loss and UV damage

  1. Double pane insulating glass unit
  2. LoE²-270 (for optional LoE coatings, see Glass Terminology)
  3. Argon gas (for exceptions, see Glass Terminology)
  4. ThermaPlus coating on indoor surface
  1. Thermo-Edge, stainless steel spacer bars

Option - Laminated Glass

Laminated glass* in one or all panes adds safety, security, sound control, and the ultimate in UV blockage

  1. Double pane insulating glass unit
  2. LoE coating options (see Glass Terminology)
  3. Argon gas (for exceptions, see Glass Terminology)
  4. Thermo-Edge, stainless steel spacer bars
  5. Laminated glass (i.e. Two pieces of glass fused together with a plastic interlayer)

*Limitations for using laminated glass may apply if products must meet specific impact or design pressure ratings; construction and structural modifications may be required to meet building codes.

Option - Neat Glass

Neat® glass goes through a special sputter-coating process to make the exterior surface ultra smooth. Water "sheets off" more readily than it would on uncoated glass, helping rinse away dirt, and therefore requiring less cleaning time (view video).

NOTE: Not available on units with specialty glass on surface #1 or 2.

Option - Preserve Protective Film

Preserve™ is an optional, protective film that protects glass from scratches during transit and construction, as well as helping to reduce the time involved in job site clean-up (view video).

NOTE: Not available on single-glazed units, units with true divided lites or other small insulating glass units, or some types of decorative glass. Contact your local Kolbe dealer for more information.

Divided Lites

The Performance Divided Lite (PDL) System

The performance divided lite (PDL) system uses double pane insulating glass units with bars adhered to the interior and exterior of the glass unit. Plus, spacer bars are held within the insulating glass unit. The visual continuity of the interior bars, spacer bars, and exterior bars creates the illusion of true divided lites.

The spacer bars allow air and/or argon gas to flow within the glass unit. Therefore, due to the large, unobstructed thermal break, the products are more energy efficient than products with true divided lites.

PDL for Standard Doors

Standard fiberglass doors are available with wood or aluminum PDL bars, depending on whether the panel is textured or smooth, whether the bars are on the interior or exterior surface, and whether they are finished, primed or unfinished. If the panel is factory-finished, the bars will be finished to complement the door panel.

PDL bars for Standard doors are available in widths of 5/8", 7/8", 1-1/8", 1-3/4", 2-1/4" and 4-1/2". The bars have a beveled profile; interior bars are available with an ovolo or square profile option. Spacer bars are a champagne color; bronze and mill finish spacer bars are optional. Custom PDL bar widths and profiles are available.

NOTE: Various circumstances – such as radius grille patterns – may require different PDL bar materials. PDL is not available on panels with blinds, venting panels, or panels with decorative glass.

Grilles-in-the-Airspace (GIA) for Standard Doors

Standard fiberglass doors are available with grilles-in-the-airspace (GIA). GIA offers the aesthetic of divided lites, without obstructing the interior or exterior glass surface, making the glass easy to clean. Aluminum bars are sealed within the insulating glass unit, allowing air and/or argon gas to flow within the glass unit. Bar types include:

  • 3/4" contoured bars
  • 5/8" flat bars
  • 5/16" pencil-shaped bars in brass or pewter

 

Finish Options:

  • White
     
  • Beige
     
  • Sand
     
  • Rustic
     
  • Hartford
    Green
  • Chutney
     
  • Light
    Wood
  • Dark
    Wood

Some may be available with:

  • Flat brass bars
  • Two-tones, i.e. one color or wood appearance option on the interior and a different one on the exterior
  • Custom patterns

NOTE: GIA options for panels with blinds and venting panels are slightly different than what is outlined here; please follow the links at left to Panels with Blinds and Venting Panels for more details. Decorative glass is not available with GIA.

Panels with No Glass

Standard Textured (ST) Panels with No Glass

  • 1
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 34
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 49
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 30
    ST
    Width:
    3-0
    Height:
    8-0
  • OG36
    ST
    Width:
    3-0
    Height:
    6-8
  • 52
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 60
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 66
    ST
    Width:
    3-0
    Height:
    6-8
  • 90
    ST
    Width:
    3-0
    Height:
    6-8
  • 86
    ST
    Width:
    3-0
    Height:
    6-8
Standard Smooth (SS) Panels with No Glass

  • 1
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 34
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 49
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 30
    SS
    Width:
    3-0
    Height:
    8-0
  • OG36
    SS
    Width:
    3-0
    Height:
    6-8
  • 52
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 60
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 66
    SS
    Width:
    3-0
    Height:
    6-8
  • 90
    SS
    Width:
    3-0
    Height:
    6-8
  • 86
    SS
    Width:
    3-0
    Height:
    6-8
  • 24
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 24AT
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0

Panels with Glass

Standard Textured (ST) Panels with Glass

  • 21
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 20
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 606
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • OG93
    ST
    Width:
    3-0
    Height:
    6-8
  • 2
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 61
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 68
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 81
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 70
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 92
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 814*
    ST
    Width:
    3-0
    Height:
    6-8
  • 4
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 819
    ST
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 38
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 33
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

Standard Smooth (SS) Panels with Glass

  • 21
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 20
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 606
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • OG93
    SS
    Width:
    3-0
    Height:
    6-8
  • 2
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 61
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 68
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 81
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 70
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 92
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 814*
    SS
    Width:
    3-0
    Height:
    6-8
  • 65
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 3C-15
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 3-15
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 25
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 4
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 819
    SS
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 38
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 33
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

  Capella Glass

Capella

  1. Micro-Iced Granite Glass
  2. Clear Bevels
  3. Thin Reed Glass
  4. Patina Caming
  5. Hammered Glass

 

Privacy Rating: 8

 

 Patina Caming

Standard Textured (ST) Panels with Capella Glass

  • 686-CPL
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 607-CPL
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-CPL
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 694-CPL
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • 422-CPL
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
Standard Smooth (SS) Panels with Capella Glass

  • 686-CPL
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 607-CPL
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8
  • 684-CPL
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 694-CPL
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • 422-CPL
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0

  Catalina Glass

Catalina

  1. Micro-Granite Glass
  2. Bronze Vein Wrought Iron

 

Privacy Rating: 9

 

 Bronze Vein Wrought Iron

Standard Textured (ST) Panels with Catalina Glass

  • 686-CTL
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-CTL
    ST
    Widths:
    2-8, 3-0
    Heights:
    8-0
  • 694-CTL
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-CTL
    ST
    Widths:
    1-0, 1-2
    Height:
    8-0
Standard Smooth (SS) Panels with Catalina Glass

  • 686-CTL
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-CTL
    SS
    Widths:
    2-8, 3-0
    Heights:
    8-0
  • 694-CTL
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-CTL
    SS
    Widths:
    1-0, 1-2
    Height:
    8-0

  Harrison Glass

Harrison

  1. Clear Glue Chip Glass
  2. Clear Bevels
  3. Clear Cluster Bevels
  4. Brass, Nickel or Patina Caming

 

Privacy Rating: 7

 

 Brass Caming

  Nickel Caming

 Patina Caming

Standard Textured (ST) Panels with Harrison Glass

  • 686-HRR
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 607-HRR
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 692-HRR
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 684-HRR
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • OG36-HRR
    ST
    Width:
    3-0
    Height:
    6-8
  • 919-HRR
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 659-HRR
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 640-HRR
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 694-HRR
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • 422-HRR
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-HRR
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
Standard Smooth (SS) Panels with Harrison Glass

  • 686-HRR
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 607-HRR
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 692-HRR
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 684-HRR
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • OG36-HRR
    SS
    Width:
    3-0
    Height:
    6-8
  • 919-HRR
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 659-HRR
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 640-HRR
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 984-HRR
    SS
    Widths:
    2-8,2-10,3-0
    Height:
    8-0
  • 694-HRR
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • 422-HRR
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-HRR
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0

  Heartland Glass

Heartland Glass

  1. Thin Reed Glass
  2. Clear Bevels
  3. Patina Caming
  4. Seedy Glass
  5. Crinkle Glass

 

Privacy Rating: 5

 

 Patina Caming

Standard Textured (ST) Panels with Heartland Glass

  • 686-HRT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-HRT
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 692-HRT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 684-HRT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 814-HRT*
    ST
    Width:
    3-0
    Height:
    6-8
  • 694-HRT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 819-HRT
    ST
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 422-HRT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-HRT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

Standard Smooth (SS) Panels with Heartland Glass

  • 686-HRT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-HRT
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 692-HRT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 684-HRT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 814-HRT*
    SS
    Width:
    3-0
    Height:
    6-8
  • 984-HRT
    SS
    Widths:
    2-8,2-10,3-0
    Height:
    8-0
  • 694-HRT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 819-HRT
    SS
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 422-HRT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-HRT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

  Martiel Glass

Martiel

  1. Arctic Glass
  2. Clear Bevels
  3. Patina Caming
  4. Clear Renaissance Glass

 

Privacy Rating: 4

 Patina Caming

Standard Textured (ST) Panels with Martiel Glass

  • 686-MAR
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-MAR
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-MAR
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-MAR
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 814-MAR*
    ST
    Width:
    3-0
    Height:
    6-8
  • 694-MAR
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8,7-0,8-0
  • 819-MAR
    ST
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 422-MAR
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-MAR
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

Standard Smooth (SS) Panels with Martiel Glass

  • 686-MAR
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-MAR
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-MAR
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-MAR
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 814-MAR*
    SS
    Width:
    3-0
    Height:
    6-8
  • 984-MAR
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 694-MAR
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8,7-0,8-0
  • 819-MAR
    SS
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 422-MAR
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-MAR
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

  Monterey Glass

Monterey

  1. Granite Glass
  2. Clear Bevels
  3. Satin Nickel or Patina Caming
  4. Micro-Granite Glass

 

Privacy Rating: 7

 

 Patina Caming

 Satin Nickel Caming

Standard Textured (ST) Panels with Monterey Glass

  • 686-MNT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 607-MNT
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-MNT
    ST
    Widths:
    2-8, 3-0
    Height:
    8-0
  • 814-MNT*
    ST
    Width:
    3-0
    Height:
    6-8
  • 694-MNT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • 819-MNT
    ST
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 422-MNT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

Standard Smooth (SS) Panels with Monterey Glass

  • 686-MNT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 607-MNT
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-MNT
    SS
    Widths:
    2-8,2-10,3-0
    Height:
    8-0
  • 814-MNT*
    SS
    Width:
    3-0
    Height:
    6-8
  • 984-MNT
    SS
    Widths:
    2-8,2-10,3-0
    Height:
    8-0
  • 694-MNT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
  • 819-MNT
    SS
    Widths:
    1-0, 1-2
    Height:
    6-8
  • 422-MNT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • *Mission-style dentil shelf available

*Matching mission-style dentil shelf available for panels indicated.

Sidelite #819 has a Craftsman-style flat frame around the glass to match door #814.

  Oxford Glass

Oxford

  1. Glue Chip Glass
  2. Glue Chip & Clear Cluster Bevels
  3. Brass or Nickel Caming
    (Patina Caming by special order)
  4. Grey Soft Wave Glass

 

Privacy Rating: 7

 

 Brass Caming

  Nickel Caming

 Patina Caming (by special order)

Standard Textured (ST) Panels with Oxford Glass

  • 686-OXF
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-OXF
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-OXF
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-OXF
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 640-OXF
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 694-OXF
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-OXF
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-OXF
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
Standard Smooth (SS) Panels with Oxford Glass

  • 686-OXF
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-OXF
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-OXF
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-OXF
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 640-OXF
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 984-OXF
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 694-OXF
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-OXF
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-OXF
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0

  Regency Glass

Regency

  1. Glue Chip Glass
  2. Clear Cluster Bevels
  3. Brass or Satin Nickel Caming
  4. Granite Glass

 

Privacy Rating: 7

 

 Brass Caming

 Satin Nickel Caming

Standard Textured (ST) Panels with Regency Glass

  • 686-REG
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-REG
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8, 8-0
  • 684-REG
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8, 8-0
  • 692-REG
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 919-REG
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • OG36-REG
    ST
    Width:
    3-0
    Height:
    6-8
  • 640-REG
    ST
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 659-REG
    ST
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 694-REG
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-REG
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-REG
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
Standard Smooth (SS) Panels with Regency Glass

  • 686-REG
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-REG
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-REG
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-REG
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • 919-REG
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • OG36-REG
    SS
    Width:
    3-0
    Height:
    6-8
  • 640-REG
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 659-REG
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    6-8
  • 984-REG
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 694-REG
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-REG
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-REG
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0

  Solitude Glass

Solitude

  1. Clear Renaissance Glass
  2. Clear Bevels
  3. Grey Renaissance Glass
  4. Nickel Caming

 

Privacy Rating: 3

 

  Nickel Caming

Standard Textured (ST) Panels with Solitude Glass

  • 686-SLT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-SLT
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-SLT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-SLT
    ST
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • OG36-SLT
    ST
    Width:
    3-0
    Height:
    6-8
  • 694-SLT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-SLT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-SLT
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0
Standard Smooth (SS) Panels with Solitude Glass

  • 686-SLT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0, 8-0
  • 607-SLT
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-SLT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 8-0
  • 692-SLT
    SS
    Widths:
    2-8, 2-10, 3-0
    Heights:
    6-8, 7-0
  • OG36-SLT
    SS
    Width:
    3-0
    Height:
    6-8
  • 984-SLT
    SS
    Widths:
    2-8, 2-10, 3-0
    Height:
    8-0
  • 694-SLT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0, 8-0
  • 422-SLT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 692-SLT
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 7-0

Flush-Glazed Doors

Panel Details

Standard flush-glazed doors have an interior glazing bead, which creates the aesthetic of a wood door. The bead profile and exterior sticking can be appreciated even further with the addition of performanced divided lites. 

  • 10 ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 10 SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0

ST = Standard Textured
SS - Standard Smooth

Panels with Blinds

Product Detail

Increase your privacy and sense of security at night by choosing Standard fiberglass doors with blinds. The blinds can be adjusted to completely block the light, plus privacy channels on each side eliminates the gaps that often occur when blinds are closed.  The fingertip control is within easy reach and design with ergonomics in mind.

These doors and sidelites are available either textured (ST) or with a smooth skin (SS).

Standard Textured (ST) Panels with Blinds

  • 607-RLB
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-RLB
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8
  • 686-RLB
    ST
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 38-RLB
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 690-RLB
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8
Standard Smooth (SS) Panels with Blinds

  • 607-RLB
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 684-RLB
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8
  • 686-RLB
    SS
    Widths:
    2-8, 3-0
    Heights:
    6-8, 8-0
  • 692-RLB
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 38-RLB
    SS
    Widths:
    1-0, 1-2
    Heights:
    6-8, 8-0
  • 690-RLB
    ST
    Widths:
    1-0, 1-2
    Heights:
    6-8
  • 692-RLB
    SS
    Widths:
    1-2, 2-8
    Height:
    6-8
Panels with Blinds, GIA and Triple Pane Glass

The Standard smooth panels shown below are available with triple pane insulating glass units. Blinds and grilles-in-the-airspace are sealed between the outer glass panes, which are tempered for safety. The blinds completely disappear into top valance when fully raised. The triple pane glass helps reduce heat transmission and suppress sound.

Standard Smooth (SS) Panels with Blinds, Grilles-in-the-Airspace & Triple Pane Glass

  • 684-CM9
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 686-CM10
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 686-CM15
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8

Venting Panels

Product Detail

Vents allow for air circulation through your secure fiberglass door panel. There are 10 adjustment locations for the latches, used to lock in your movable glass insert for varying degrees of ventilation. The frame is made with a UV-resistant injection-molded frame. 

Venting doors are available with low emissivity glass, except for those with Rain glass.

  • 2V Clear*
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 2V Rain
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 61V-12L2V Clear*
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 61V-12L2V Rain
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 61V Clear*
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8
  • 61V Rain
    SS
    Widths:
    2-8, 3-0
    Height:
    6-8

*These units are available with low emissivity glass.

Handle Sets & Locks

Standard

  • No handles, locks or boring

Option - Prep for Field-Applied Hardware

  • Single bore
  • Double bore
  • Custom boring

Option - Locking Hardware

  • Keyed handle sets
  • Two-point flush bolts on the less active panel of French doors
  • Single-point locking hardware
  • Multi-point locking hardware with weather-resistant, stainless steel operator parts and hardware channels

Option - Toronto Handle Sets

Toronto handle sets are available for most inswing and outswing doors. 

  • Bright Brass PVD
  • Antique Brass
  • Antique Nickel PVD
  • Matte Black
  • Oil-Rubbed
  • Satin Nickel PVD
  • Smoky Gray PVD
  • Rustic Umber

NOTES:

  • Oil-rubbed is a living finish which will change appearance over time.
  • PVD (Physical Vapor Deposition) finish is an application over the color which helps protect the  finish from tarnishing, peeling and cracking.

Option - Verona Handle Sets

Verona handle sets are available for most inswing and outswing doors.

  • Bright Brass PVD
  • Antique Brass
  • Antique Nickel PVD
  • Matte Black
  • Oil-Rubbed
  • Satin Nickel PVD
  • Smoky Gray PVD
  • Rustic Umber

NOTES:

  • Oil-rubbed is a living finish which will change appearance over time.
  • PVD (Physical Vapor Deposition) finish is an application over the color which helps protect the finish from tarnishing, peeling and cracking.
  • Smoky Gray is shown with optional keyed lock cylinder.

Option - München Handle Sets

München handle sets are available for most inswing and outswing doors. 

  • Bright Brass PVD
  • Antique Brass
  • Antique Nickel PVD
  • Matte Black
  • Oil-Rubbed
  • Satin Nickel PVD
  • Smoky Gray PVD
  • Rustic Umber

NOTES:

  • München handles are not available on doors with 3" wide stiles.
  • Oil-rubbed is a living finish which will change appearance over time.
  • PVD (Physical Vapor Deposition) finish is an application over the color which helps protect the finish from tarnishing, peeling and cracking.

Option - Dallas Handle Sets

Dallas handle sets are available for most inswing and outswing doors. 

  • Bright Brass PVD
  • Satin Nickel PVD
  • Matte Black
  • Smoky Gray PVD

NOTE: PVD finish is an application over the color that helps protect the finish from tarnishing, peeling and cracking.

NOTE:

On-screen images of finishes and colors may vary slightly from actual colors. Selections should be made based on actual color samples from your local dealer. Prices may vary depending on the color or finish chosen.

Hinges

Residential, Non-Adjustable Hinges

4" x 4" non-adjustable ball-bearing hinges with 1/4" radius corners are standard for wood and wood/clad outswing doors, standard for fiberglass doors, and optional for wood and wood/clad inswing doors

  • Bright Brass
  • Antique Brass
  • Satin Nickel
  • Oil-Rubbed*
  • Matte Black
  • Antique Nickel
  • Stainless Steel

*Oil-rubbed is a "living finish" which will change appearance over time

Residential, Adjustable Hinges

4" x 3-5/8" adjustable hinges with 5/8" radius corners are standard for wood and wood/clad inswing doors, optional for wood and wood/clad outswing doors, and optional for most fiberglass doors.

  • Bright Brass*
  • Antique Brass
  • Satin Nickel
  • Oil-Rubbed**
  • Matte Black
  • Antique Nickel
     
  • Gold-Painted
     
  • Brushed
    Chrome PVD†
  • Smoky Gray
    PVD†
  • Rustic Umber
     
  • Silver

*Also available with PVD finish – which is an application over the color that helps protect the hardware against tarnishing, peeling and cracking

**Oil-rubbed is a "living finish" which will change appearance over time

†Brushed Chrome and Smoky Gray are not available without PVD

Commercial, Non-Adjustable Hinges

Commercial-grade, non-adjustable, 4 x 4 ball-bearing hinges with square corners are standard for commercial doors and optional for all other swinging doors. 4-1/2 x 4-1/2 hinges are available as indicated.

  • Bright Brass
    4 x 4
    4-1/2 x 4-1/2
  • Antique Brass
    4 x 4
     
  • Satin Nickel
    4 x 4
     
  • Oil-Rubbed*
    4 x 4
    4-1/2 x 4-1/2
  • Matte Black
    4 x 4
     
  • Stainless Steel
    4 x 4
    4-1/2 x 4-1/2

*Oil-rubbed is a "living finish" which will change appearance over time

NOTE:

On-screen images of finishes and colors may vary slightly from actual colors. Selections should be made based on actual color samples from your local dealer. Prices may vary depending on the color or finish chosen.

Sills for Inswing Doors

Standard - Weep Sills

  • Bronze-Anodized Weep Sill
  • Clear Anodized Weep Sill
Option - Adjustable Sills

  • Bronze-Anodized
    Adjustable Sill
    (with nosing extension)
  • Clear-Anodized
    Adjustable Sill
     
Option - Wood Sills

  • Oak wood species
  • Mahogany wood species
  • Not recommended for use in high moisture conditions

  • Oak Sill for Inswing Doors
Option - ADA Sills

See Universal Design above left.

Sills for Outswing Doors

Standard - Bumper Sills

  • Bronze anodized finish (shown)
  • Clear anodized finish

  • Bronze-Anodized Bumper Sill
Option - Wood Sills

  • Oak wood species (shown)
  • Mahogany wood species
  • Not recommended for use in high moisture conditions

  • Oak Sill for Outswing Doors
Option - ADA Sills

See Universal Design above left.

Universal Design

Option - Lever Handles

  • Operate more easily than door knobs
  • Available in a variety of styles and finishes (examples shown; see Handle Sets & Locks for current style and finish options)

  • Bright Brass PVD
  • Antique Brass
  • Antique Nickel PVD
  • Matte Black
Option - ADA-Compliant Sills for Inswing & Outswing Doors

  • Creates a flush surface for easy access to pass through
  • Incorporates a thermal break for cold climates
  • Bronze-anodized finish (shown)
  • Clear-anodized finish

  • Bronze-Anodized ADA Sill
Option - ADA-Compliant Sills for Outswing Doors

  • Creates a flush surface for easy access to pass through
  • No thermal break
  • Bronze-anodized finish (shown)
  • Clear-anodized finish

  • Bronze-Anodized ADA Sill
    (no Thermal Break)

Panels

Standard - Unfinished

The exterior of door and sidelite panels are unfinished as standard.

Option - Factory-Finished Stain

Five stain colors are available for the exterior of textured panels.

  • Cherry
  • Lt. Oak 998
  • Red Wheat
  • Spiced Walnut
  • Sunset Oak

Please select colors based on actual samples from your dealer.

Option - K-Kron II Exterior Finish

K-Kron II colors are available for most Heritage Series wood products and the panels of Fiberglass doors. It is a three-step process: 1) Wood pieces are immersed in a preservative for protection from water, insects and fungus, 2) A high performance urethane primer is applied to help seal the wood and provide a tough bonding surface, 3) the topcoat finish is applied using an airless, control-spray system that ensures complete, consistent coverage. (Learn more). Kolbe offers an extensive array of colors, as well as custom colors.

  • Highest quality warranted finish for exterior wood substrates in the industry
  • Resists ultraviolet deterioration and chalking, chemical attack, as well as damage from salt, wind, sleet and snow
  • 10-year film integrity warranty extended directly to the homeowner (view Warranties)

  •  
    Ultra Pure White
  •  
    White
  •  
    Abalone
  •  
    Alabaster
  •  
    Rustic
  •  
    Sand
  •  
    Mudpie
  •  
    Beige
  •  
    Spiced Vinegar
  •  
    Camel
  •  
    Natural Cotton
  •  
    Gingersnap
  •  
    Truffle
  •  
    Slate
  •  
    Frosted Jade
  •  
    Kiwi
  •  
    Bayleaf
  •  
    Pumpkin Spice
  •  
    Butterscotch
  •  
    Hartford Green
  •  
    Mystic Ivy
  •  
    Green Tea Leaf
  •  
    Basil
  •  
    Manchester
  •  
    Chutney
  •  
    Antique Red
  •  
    Merlot
  •  
    Patriotic Blue
  •  
    Cape Cod
  •  
    Waterford
  •  
    Timberwolf

NOTE: Please make color selections using actual samples from your local dealer. For custom colors, please provide a sample to your dealer.

Clad Frame

Standard - Frame Construction

  • Durable .050" thick cladding of 6063 extruded aluminum alloy, press-fit onto the exterior wood frame
  • Accessory grooves are integral to the frame for easy addition of extruded trims and sill nosings

  • Clad Frame
Standard - Fluoropolymer Exterior Finish

  • 70% PVDF fluoropolymer exterior finish
  • Meets performance requirements of AAMA 2605-13 – the most stringent testing procedures for organic coatings on aluminum extrusions
  • Resists chemicals, abrasion, corrosion, chalking and erosion
  • Maintains film integrity, retains the color and gloss
  • 30-year warranty extended directly to the homeowner (view Warranties)

  •  
    Ultra Pure White
  •  
    White
  •  
    Abalone
  •  
    Alabaster
  •  
    Rustic
  •  
    Sand
  •  
    Mudpie
  •  
    Beige
  •  
    Spiced Vinegar
  •  
    Camel
  •  
    Natural Cotton
  •  
    Gingersnap
  •  
    Truffle
  •  
    Coal Black
  •  
    Slate
  •  
    Frosted Jade
  •  
    Kiwi
  •  
    Bayleaf
  •  
    Pumpkin Spice
  •  
    Butterscotch
  •  
    Hartford Green
  •  
    Mystic Ivy
  •  
    Green Tea Leaf
  •  
    Basil
  •  
    Manchester
  •  
    Chutney
  •  
    Antique Red
  •  
    Merlot
  •  
    Patriotic Blue
  •  
    Cape Cod
  •  
    Waterford
  •  
    Timberwolf

NOTES: Actual finish colors may vary from on-screen images. Please make selections using color samples from your local dealer. Custom color are also available. For custom colors, please provide a sample to your dealer.

Option - Anodized Exterior Finish

Anodized finishes are created using an electrolyte process with oxide film to coat the aluminum cladding. This results in a reflective, metallic sheen.

  • Clear
  • Champagne
  • Light Bronze
  • Medium Bronze
  • Dark Bronze
  • Black
  • Auburn

NOTES: An acceptable light to dark color range is up to 5 Delta E’s, per AAMA 611-98 specifications, Section 8.3. This is due to variables which include (but are not limited to) part shapes, alloy variations and time in the anodizing process. This means that a sash part could appear slightly different in color than a frame part. This is considered acceptable. Samples of the color range are available upon request; even samples provided may vary from the final product due to these variables.

These are specialty colors which will incur an added charge and possible longer lead times. Actual finish colors may vary from on-screen images. Please make selections using color samples from your local dealer. For custom colors, please provide a sample to your dealer.

Option - Mica Exterior Finish

Mica finishes are available on extruded aluminum clad products. They are fluoropolymer, but with mica flakes within the coating. This catches the light and results in vibrant, dimensional colors. 

  • 70% PVDF fluoropolymer exterior finish with mica flakes
  • Meets performance requirements of AAMA 2605-13 – the most stringent testing procedures for organic coatings on aluminum extrusions
  • Resists chemicals, abrasion, corrosion, chalking and erosion
  • Maintains film integrity, retains the color and gloss
  • 30-year warranty extended directly to the homeowner (view Warranties)

  • Cashmere Pearl
  • Driftwood
  • Espresso
  • Hazelnut
  • Autumn Spice
  • Golden Harvest
  • Pesto
  • Pearlescent White
  • Galaxy Silver
  • Silverstorm
  • Cosmic Gray
  • Night Sky
  • Café Noir

NOTES: These are specialty colors which will incur an added charge and possible longer lead times. Actual finish colors may vary from on-screen images. Please make selections using color samples from your local dealer. For custom colors, please provide a sample to your dealer.

Option - Extruded Aluminum Brickmould

Extruded aluminum trim is designed to offer architectural aesthetics similar to wood trim, with the added benefit of greater durability and lower maintenance. Plus, extruded aluminum billet consists of 50-75% recycled material.

In most cases, the same color is chosen for the trim as for the window or door frame and sash. Combinations are possible, however. See the Tivoli Student Union project for an example of complementary colors used on sash vs. frame and trim, as well as custom trim profiles created for the project. Please contact your local Kolbe dealer to explore the possibilities of creating a custom trim profile.

  1. Ogee casing
  2. Stucco trim casing
  3. Pavilion brickmould
  4. Bull nose casing
  5. 1-5/8" brickmould
  6. 1-15/16" brickmould
  7. 2" flat casing
  8. 2" flat casing with backband
  9. Historic brickmould
  10. 3-1/2" profiled brickmould
  11. 3-1/2" flat casing
  12. 3-1/2" flat casing with backband
  13. Beaded casing
  14. Beaded casing with backband

NOTES: Limitations apply when combining trim options; i.e., not all brickmould profiles can be combined with all sill nosing profiles, and not all profiles are available for radius units.

Wood Frame

Standard - Frame Construction

  • Pine frame, exterior finished with latex primer
  • 1-15/16" brickmould exterior trim applied

  • Wood Frame
  • Pine
Wood Species

Standard

  • Pine sash and interior stops

Option

  • Other wood species may be available upon request; those shown are a small example of what may be available

  • Pine
  • Alder
  • Fir
  • Maple
  • Cherry
  • Oak
  • Walnut
  • Mahogany
  • Bamboo

NOTES: Because wood varies by nature, the actual wood used in our products may vary in grain and color from that shown here. Selections should be made based on actual samples.


Option - K-Kron II Exterior Finish

K-Kron II colors are available for most Heritage Series wood products and the panels of Fiberglass doors. It is a three-step process: 1) Wood pieces are immersed in a treatment for protection from water, insects and fungus, 2) A high performance urethane primer is applied to help seal the wood and provide a tough bonding surface, 3) the topcoat finish is applied using an airless, control-spray system that ensures complete, consistent coverage. (Learn more). Kolbe offers an extensive array of colors, as well as custom colors.

  • Highest quality warranted finish for exterior wood substrates in the industry
  • Resists ultraviolet deterioration and chalking, chemical attack, as well as damage from salt, wind, sleet and snow
  • 10-year film integrity warranty extended directly to the homeowner (view Warranties)

  •  
    Ultra Pure White
  •  
    White
  •  
    Abalone
  •  
    Alabaster
  •  
    Rustic
  •  
    Sand
  •  
    Mudpie
  •  
    Beige
  •  
    Spiced Vinegar
  •  
    Camel
  •  
    Natural Cotton
  •  
    Gingersnap
  •  
    Truffle
  •  
    Slate
  •  
    Frosted Jade
  •  
    Kiwi
  •  
    Bayleaf
  •  
    Pumpkin Spice
  •  
    Butterscotch
  •  
    Hartford Green
  •  
    Mystic Ivy
  •  
    Green Tea Leaf
  •  
    Basil
  •  
    Manchester
  •  
    Chutney
  •  
    Antique Red
  •  
    Merlot
  •  
    Patriotic Blue
  •  
    Cape Cod
  •  
    Waterford
  •  
    Timberwolf

NOTE: Please make color selections using actual samples from your local dealer. For custom colors, please provide a sample to your dealer.

Option - Exterior Wood Trim

Accentuate the beauty of your doors & folding windows with exterior brickmould casing:

  1. 1-15/16" profiled brickmould (standard on Heritage Serie products)
  2. 3-1/2" profiled brickmould
  3. 3-1/2" flat casing
  4. 3-1/2" profiled brickmould with backband
  5. 3-1/2" flat casing with backband

NOTES: The window corner sections above show brickmould and sill nosing, however sill nosing does not apply to doors or folding windows.

Custom trim is available, contact your local Kolbe dealer for more information.

Option - Accessories

For extraordinary accent, consider the following wood decorative accessories:

  1. Pediment head
  2. Keystones
  3. Rosettes
  4. Corner Blocks
  • Dentil moulding
  • Other custom wood moulding or trim


Panels

Standard - Unfinished

Unfinished on the interior unless requested otherwise.

Option - Factory-Finished Stain

Five stain colors are available for the interior of textured fiberglass panels.

  • Cherry
  • Lt. Oak 998
  • Red Wheat
  • Spiced Walnut
  • Sunset Oak

Please select colors based on actual samples from your dealer.

Option - Factory-Applied Paint

After being factory-primed, a topcoat of water-based, acrylic type latex paint is applied. Custom colors may be requested.

  •  
    Bright White
  •  
    Ultra Pure White
  •  
    Abalone
  •  
    Silk
  •  
    Ivory Tusk
  •  
    Natural Cotton
  •  
    Beige

NOTE:  On-screen images of interior finishes may vary from actual colors.  Selections should be made based on actual color samples.  Limitations may apply; contact your local Kolbe dealer for more information.

Interior Trim

Option - Interior Trim

Accent the interior of windows and doors with interior casing.

  • 2-1/8" wide ranch casing (1) or 2-1/4" wide colonial casing (2) in pine or oak
  • Radius casing
  • Specialty mouldings are available in pine, oak and other wood species
  • Shipped loose for field application

 

Option - Corner Blocks

Giving windows and doors a signature look has never been easier. Complement the interior with:

  • Corner blocks
  • Rosettes
  • Available in pine or oak


Drawing Files - Sizes / Elevations for Standard Fiberglass Doors

Rough Opening Statement

Download: All files below

  PDF
Formulas & Charts
   Sizes, Dimension Calculations & Hinging
Rough Opening Statement
   This information is essential for accurate planning.

Drawing Files - Section Details for Standard Fiberglass Doors

Download: All files below

  DWG DXF PDF
Ultra Series Frame
   1-Wide Active Inswing Door - Horiz
   1-Wide Stationary Inswing Door - Horiz
   2-Wide Active/Stationary Inswing Door - Horiz
   2-Wide Stationary/Active Inswing Door - Horiz
   2-Wide French Inswing Door - Horiz
   Active Inswing Door with Weep Sill - Vert
   1-Wide Active Outswing Door - Horiz
   1-Wide Stationary Outswing Door - Horiz
   2-Wide Active/Stationary Outswing Door - Horiz
   2-Wide Stationary/Active Outswing Door - Horiz
   2-Wide French Outswing Door - Horiz
   Active Outswing Door with Bumper Sill - Vert
Heritage Series Frame
   1-Wide Active Inswing Door - Horiz
   1-Wide Stationary Inswing Door - Horiz
   2-Wide Active/Stationary Inswing Door - Horiz
   2-Wide Stationary/Active Inswing Door - Horiz
   2-Wide French Inswing Door - Horiz
   Active Inswing Door with Weep Sill - Vert
   1-Wide Active Outswing Door - Horiz
   1-Wide Stationary Outswing Door - Horiz
   2-Wide Active/Stationary Outswing Door - Horiz
   2-Wide Stationary/Active Outswing Door - Horiz
   2-Wide French Outswing Door - Horiz
   Active Outswing Door with Bumper Sill - Vert

Drawing Files - All Files for Standard Fiberglass Doors

Download files for this product: (does not include related product models)

Download: DWG files

Download: DXF files

Download: PDF files

All of the above


Use links at left to view detailed descriptions of individual files. Each page
includes a downloadable zip file of drawings in that category.


Finish Performance

K-Kron II Finish Performance

  • High performance finish
  • Resists ultraviolet deterioration and chalking, chemical attack, as well as damage from salt, wind, sleet and snow
  • 10-year film integrity warranty extended directly to the homeowner (view Warranties)
  • Warranty is transferable to subsequent homeowners
  • Over 30 vibrant colors to choose from (see Exterior tab)
  • Custom colors are available; simply provide a sample to your dealer

 

Three-steps to applying the K-Kron II exterior finish system
  1. Before assembly, wood pieces of the window or door are immersed in a treatment with both an insecticide and a fungicide -- helping the exterior wood surfaces resist decay. This treatment meets standards set by WDMA I.S.4-2000.
  2. The windows or doors are assembled. Before installing the glass, two coats of a specially-formulated urethane primer by Akzo Nobel is applied -- helping to seal the wood and provide a bonding surface for the final topcoat. The primer is applied using a controlled-spray process which follows WDMA T.M. 11-2000 guidelines.
  3. Finally, a high performance urethane topcoat is applied. An airless, multi-step, controlled-spray system ensures complete, consistent coverage of the exterior wood surfaces. The result? Beautifully protected windows and doors.

The K-Kron II three-step exterior finishing system follows WDMA T.M. 12-2000 guidelines.

Film Characteristics & Properties of K-Kron II

Applies to units of Ponderosa pine, sugar pine, Douglas fir, helmock and other select wood species.

Film Characteristics:           

Two coats high performance urethane exterior primer followed with one coat K-Kron II exterior colored topcoat1

Colors Available:

31 standard colors; custom colors available

Gloss:
@ 60°2 ASTM D 523-89 (1999)

35 +/- 5

Dry Film Thickness:

Average total dry film thickness equals 6.0-7.0 mils (4.0-4.5 mils primer and 2.0-2.5 mils topcoat)

Color Uniformity:
ASTM E 1164-02

Color instrumentally and visually controlled

Dry Film Adhesion (Crosshatch):
ASTM Method D 3359-02 (Method B, 6 cuts) (WDMA T.M. 12-2000, 5.2.1)

2B or better after tape is pulled off

Wet Film Adhesion:
(24 hours @100°F followed by 24 hour dry) (WDMA T.M. 12-2000, 5.2.2)

2B or better after tape is pulled off

Boiling Water Resistance:
(WDMA T.M. 12-2000, 5.2.3)

2B or better after tape is pulled off

Muriatic Acid Resistance:
(WDMA T.M. 12-2000, 5.6)

15 minutes - no effect

Chemical Resistance:
ASTM D 1308-02
(WDMA T.M. 12-2000, 5.3)

Pass - no damaging effect

Freeze/Thaw Cycling:
ASTM D 1211-97
(WDMA T.M. 12-2000, 5.4)

Pass - no damaging effect (33 cycles complete)

Impact Resistance:
ASTM D 2794-93 (2004)

Pass - no paint removal

Mortar Resistance:
(WDMA T.M. 12-2000, 5.7)

Pass - no loss of film, no visual change after water and/or 10% muriatic acid solution clean-up

Blocking Test:
(WDMA T.M 12-2000, 5.8)

Pass - no part-to-part blocking

Weathering Resistance -
Color Retention:
ASTM G155-04a

Max. 5 Delta E Units color change

Outdoor Exposure
WDMA T.M. 3:

Exposed to Southern Florida, Phoenix, Arizona and Wisconsin. (Representing hot humid, dry and industrial climates)

Accelerated Weathering Test:
ASTM G155-04a

Pass - film maintained integrity and also examined for adhesion, checking, cracking, peeling, separation, chalking, dirt retention, mildew and changes in color and gloss

Abrasion Resistance,
Falling Sand
ASTM D 968-93 (2001) Method A

20,000 - 24,000 liters sand/mil of coated film

1 System available to approved applicators only.

2 American Society for Testing & Materials

NOTE: K-Kron II color selectors are available through Kolbe dealers. For an accurate, computerized color match, please take a K-Kron II sample to a local paint supplier.


Warranties

Warranties

For information relating to warranties, please contact your local Kolbe dealer.

Fiberglass Doors (Effective July 1, 2014)
Twenty-five (25) Years, Fiberglass Door Panels | Ten (10) Years, Insulating Glass
Limitations Apply

Install/Maintain

Fiberglass Doors

Aug 01, 2005 - SKU# 5106600 - 374kb

Methods for installing Kolbe fiberglass doors with wood or aluminum clad frames. Preparing the rough opening & unit, sealant & flashing, insulation, finishing, maintenance & more.

Ultra, Heritage, Classic Series & Fiberglass Swinging Doors

Jan 01, 2015 - SKU# 5142290 - 1148kb

Methods for installing Kolbe outswing and inswing entrance doors. Includes tools required, preparing the rough opening & unit, sealant & flashing, installing the hardware, insulation, finishing, maintenance & more.



Text Size: A A