Table of Contents Table of Contents
Previous Page  13 / 224 Next Page
Information
Show Menu
Previous Page 13 / 224 Next Page
Page Background

Casements | “S” Series (1'-4" wide)

1'-4"

1'-4 1/2"

10 5/8"

9 7/8"

F.S.

R.O.

G.S.

G.S.*

2'-8"

2'-8 1/2"

10 5/8"

9 7/8"

4'-0"

4'-0 1/2"

10 5/8"

9 7/8"

5'-4"

5'-4 1/2"

10 5/8"

9 7/8"

6'-8"

6'-8 1/2"

10 5/8"

9 7/8"

2'-0"

2'-0 1/2"

18 5/8"

17 7/8"

2'-6"

2'-6 1/2"

24 5/8"

23 7/8"

3'-0"

3'-0 1/2"

30 5/8"

29 7/8"

3'-6"

3'-6 1/2"

36 5/8"

35 7/8"

4'-0"

4'-0 1/2"

42 5/8"

41 7/8"

4'-6"

4'-6 1/2"

48 5/8"

47 7/8"

5'-0"

5'-0 1/2"

54 5/8"

53 7/8"

5'-6"

5'-6 1/2"

60 5/8"

59 7/8"

6'-0"

6'-0 1/2"

66 5/8"

65 7/8"

“S” Series

KUS12† KUS22†

KUS32†

KUS42†

KUS52†

KUS13 KUS23

KUS33

KUS43

KUS53

KUS14 KUS24

KUS34

KUS44

KUS54

KUS15 KUS25

KUS35

KUS45

KUS55

KUS16 KUS26

KUS36

KUS46

KUS56

KUS156 KUS256

KUS356

KUS456

KUS556

KUS146 KUS246

KUS346

KUS446

KUS546

KUS136 KUS236

KUS336

KUS436

KUS536

KUS126† KUS226†

KUS326†

KUS426†

KUS526†

NOTE: All measurements are nominal. Elevation charts are not to scale. Above sizes are available as crank-out, crank-out EP and push-out casements. For push-out

casements, have dealer specify push-out when placing order for unit.

Specify stationary, left or right venting when ordering single units. Venting is viewed from the exterior.

Divided lites are optional.

Some installation procedures will require a larger rough opening than noted

(i.e. installations utilizing our installation clips)

, therefore, you may need to increase the rough

opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/2" on all sides and still be within good practice guidelines. For rough opening

recommendations, see pg. 208.

* Glass size for push-out casements.

† These Push-out units are only available with single-point hardware

F.S. = Frame Size • R.O. = Rough Opening • G.S. = Glass Size

(Glass sizes are shown per sash.)

13

Kolbe Ultra Series

Height

Elevation charts provide frame sizes for units without brickmould.

Below are the calculations to determine overall unit dimensions for

units with 1 15/16" brickmould, 3 1/2" casing with traditional sill nosing

or 3 1/2” flat casing and backband with 2 1/8" projected sill nosing.

1 15/16" brickmould; F.S. to U.D +2 5/8" +1 15/16"

3 1/2" flat or profiled casing; F.S. to U.D +5 1/2" +3 3/8"

3 1/2" flat casing & backband; F.S. to U.D. +7" +4 11/16"

Dimension Calculations

F.S. to Sash O.S.M.

-1 7/8" -1 7/8"

Sash O.S.M. to G.S.

-3 1/2" -3 1/2"

G.S. to D.L.O.

-1"

-1"

G.S. to Screen O.S.M.

+2 1/16" +13/16"

F.S. to G.S.

(for push-outs)

-6 1/8" -6 1/8"

Note: Clear opening dimensions can be found on pg. 208-209.

Width

F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside Measurement

D.L.O. = Daylight Opening • U.D. = Unit Dimension